|
 |
|
|
|
 |
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 |
download
full CB10D specs in .pdf 
| Features |
0.38 Inch Profile Remote
Turn On / Output Status(TTL) Output
Overvoltage Protection Output
Overcurrent Protection Outputs
Isolated Allowing Any Combination of Output Voltages and Polarity Fixed
Frequency (500KHz) Conversion High
Temperature Burn-In 100%
Environmental Screening (M Models) |
| How to Order |
 |
Model Numbering Example:
An environmentally screened, 10 watts, dual output, 5Vdc
and 15 Vdc, the model number would be CB10M/5/15. A
non-environmentally screened dual output, 12 Vdc and 15
Vdc, would be model number CB10D/12/15. The first output
voltage in the model number is located on channel 1, and
the second output voltage in the model number is located
on channel 2. (see case drawing)
| How To Order | |
| Series: | CB |
| Total Output Power: | 10 Watts |
| Output: | "D" for Dual |
| Product Grade: | "M"
for Military "I" for Industrial |
| Output Voltage: | 2/3.3/5/5.2/12/15 |
|
|
|
| Accessory Product | |
| EMI Filter | CBF30 |
| Selection Chart | |||
| Nominal Output (Vdc) | Dual Output Per Channel Output Current (Amps) | Model Number (Industrial) | Model Number (Military) |
|---|---|---|---|
| 2.0 | 1.0 | CB10DI/2 | CB10DM/2 |
| 3.3 | 1.0 | CB10DI/3.3 | CB10DM/3.3 |
| 5.0 | 1.0 | CB10SI/5 | CB10DM/5 |
| 5.2 | 0.96 | CB10DI/5.2 | CB10DM/5.2 |
| 12 | 0.42 | CB10DI/12 | CB10DM/12 |
| 15 | 0.33 | CB10DI/15 | CB10DM/15 |
| Input Characteristics | ||||
| Min | Typ | Max | Units | |
|---|---|---|---|---|
| Input Voltage | 14 | 28 | 40 | Vdc |
| Brown Out (75%) Full Load | 12.2 | 12.6 | Vdc | |
| No Load Power Dissipation | 1200 | 1400 | mw | |
| Inrush Charge | 200 | µC | ||
| Reflected Ripple Current | 8 | % | ||
| Logic Disable Current (Sink) | 150 | 175 | µA | |
| Logic Disable Power In | 175 | 200 | W | |
| Efficiency (Full Load) | 75 | 78 | % | |
| Efficiency (3.3Vdc) | 70 | 73 | % | |
| Efficiency (2Vdc) | 60 | 63 | % | |
| EMI | Units conform to MIL-STD-461D (on the input leads) with companion filter |
| Input Transient | Units can withstand 50V transients for up to 0.1 second |
| Output Characteristics | ||||
| |
Min | Typ | Max | Units |
|---|---|---|---|---|
| Set Point Accuracy | 25 | 50 1 | mV | |
| Load Regulation | 0.05 | 0.2 4 | % Vout | |
| Line Regulation | 0.05 | 0.2 4 | % Vout | |
| Ripple P-P (10 MHz) | 40 | 100 2 | mV | |
| Overvoltage Protection | 125 | % Vout | ||
| Transient Response (Vout) Time/Overshoot | ||||
| 20-80% Load | 150/125 | 500/ |
µS/mV | |
| Low Line-High Line | 100/200 | 500/ 250 3 |
µS/mV | |
| 50-100% Load | 100/80 |
500/ 250 3 |
µS/mV | |
| Temperature Drift | 0.01 | 0.05 | %/ °C | |
| Long Term Drift | 0.01 | 0.02 | %/1KHrs | |
| Current Term Limit | 105 | 130 | 160 | % Iout |
| Short Circuit Current | 80 | 120 | % Iout | |
| Turn on Time | 2.5 | 10 | mS | |
| Logic Turn On Time | 1 | 5 |
mS | |
| Remote Turn On | 4.5 | V | ||
| Remote Turn Off | 0.8 | V | ||
|
1
1% or 50mV, whichever is greater 2 1% or 100mV, whichever is greater 3 5% or 250mV, whichever is greater 4 0.2% or 10mV, whichever is greater |
||||
| Temperature Characteristics | ||||
| Min | Typ | Max | Units | |
|---|---|---|---|---|
| Operating | -55 | +100 | °C | |
| Storage (Max.still ambient FL) | +70 | °C | ||
| Storage (Ambient) | -55 | +125 | °C | |
| Thermal Resistance Case - Ambient | 22.6 | °C /W | ||
| Isolation Characteristics | ||
| Min | Units | |
|---|---|---|
| Isolation: | ||
| Input to Output | 500 | Vdc |
| Output to Case | 250 | Vdc |
| Input to Case | 250 | Vdc |
| Insulation Resistance(@50Vdc) | 50 | MOhm |
| Environmental Screening - M Model | |
| Stablization Bake: | +125 °C for 24 hours similar to Mil-Std-883, M1108, Condition B |
| Temperature Cycling: | 10 cycles at -55 °C to +125 °C (transition period 5 °C / min.) similar to Mil-Std-883, M1010, Condition B |
| Burn-in: | 160 hours @ 85 °C min. with Vin = 28 Vdc and output at full load |
| Final Testing | |
| See "Guide to Operation" for full details. | |
| Environmental Screening - I Model | |
| Burn in: | 16 hours @85 °C min. with Vin = 28 Vdc and output at full load |
| Final Testing | |
| See "Guide to Operation" for full details. | |
| Mechanical Characteristics | ||
| Weight | 1.06 30 |
oz. grams |
| Size | 2.0
x 1.0 x 0.38 50.8 x 25.4 x 9.7 |
inch mm |
| Volume | 0.76 12.6 |
inch3 cm3 |
| Material | Pin Case |
Brass
(Solder Plating) Alumimum 5052-H32 |
| Finish | Nickel Plating | |
[Products]
[Request Info.] [Terms & Conditions]
[Warranty Information]
[Engineering Department]
[EMI Reports] [Environmental
Reports] [Product Search]